Prevent Common and Costly Bumper Scratches With miniBumpers™.
Bumper scratches caused by your protruding front license plate screws to another vehicle's rear bumper can cost up to $500 or more to repair.
With miniBumpers™, we've got you (and them) covered! No need for bulky, costly or difficult-to-install solutions. miniBumpers™ may look small, but they can take a punch!
Get 10% OFF Your Entire Cart With Two or More Orders
- Quick, easy and effective all-in-one license plate screw and bumper protection "necessory".
- Fully encloses most protruding front license plate screws or bolts (including any accompanying washers) on a car, pickup truck, minivan or SUV (early & late model, foreign & domestic)
- Unique and compact design prevents those screws from causing scratches to another vehicle's bumper during slow-speed, low-impact contact in traffic at an intersection or when parking
- Minimizes license plate coverage
- Each order = 2 miniBumpers™ = protection for 2 front license plate screws (many front license plates have only two top screws) - check yours to see how many you will need
- Installation time is approximately 60 seconds per order (see installation video above and instructions below)
- Can often be installed right onto an existing license plate frame
- Made from a high-quality, durable thermoplastic elastomer with no messy adhesives to apply or foam pieces to fall off
- Available in black only
- Shipping costs not included
- Free pickup available at our Toronto office
Please allow 24 - 48 hours for order processing and we never charge handling fees.
For customer service, please email contact@minibumpers.com
------------------------------------------------------------------------------------------
Installed dimensions:
Base Pad Length: 2 inches (5 cm)
Base Pad Height: 1.2 inch (3 cm)
Base Pad Width: .5 inches (1.3 cm)
Maximum screw head/washer height: .2 inches (.5 cm)
Maximum screw head/washer diameter: .85 inches (2 cm)
miniBumpers™ Installation Instructions:
1. Select the appropriate tool to remove your front license plate screws or bolts
2. When ready to install, remove miniBumpers™ from their separate packaging
3. Remove only one of the front license plate screws, including any corresponding washer
4. Detach Screw Cap from one Base Pad and insert removed license plate screw, along with any corresponding washer, through hole in Base Pad
5. Reinsert the license plate screw, along with Base Pad, into its previous location on bumper so that Base Pad lies in a horizontal position (longest dimension along top of license plate)
6. Place the Screw Cap into opening in Base Pad to cover the screw head and press edges until flush with Base Pad)
7. Repeat steps 3-6 with each remaining front license plate screw or bolt
PLEASE NOTE:
miniBumpers™ are a bumper protection accessory that help prevent scratches to another vehicle’s bumper when the cause is limited to damage made by the impact of your protruding front license plate during slow-speed, low-impact contact.
Brite-Size Creations Inc. does not guarantee that miniBumpers™ will prevent all damage that may result from a collision, regardless of cause, as the amount and extent of damage will depend on many factors during impact including, but not limited to, speed, angle and point of contact, amount and type of forces applied, as well as the height differential between the respective bumpers.
The only express warranties applicable to this product are those contained within the Ontario Sale of Goods Act or the similar Act applicable to the sale of consumer goods in the province or state in which you purchased this product. Brite-Size Creations Inc. makes no other warranties, express or implied, and expressly disclaims all other warranties, including the implied warranties of merchantability and fitness for a particular purpose.
CAUTION: Brite-Size Creations Inc. does not guarantee that miniBumpers™ are authorized to be affixed on a license plate in the jurisdictions where the vehicle will be driven. By installing this product on your vehicle, you warrant that you have ensured that miniBumpers™ complies with the federal, provincial, state, municipal, and local statutes, bylaws, laws and regulations of the jurisdiction in which the vehicle will be driven. You further agree to release and hold harmless Brite-Size Creations Inc. from any losses, damages, penalties, fees, fines, or liability you may incur as a result of any and all use of miniBumpers™, including but not limited to penalties, fees, and fines levied for use in a jurisdiction where such products are not permitted.
miniBumpers™ are protected by the following patents:
CA Patent No. 3,002,316
US Patent No. 10,696,256